RecallLookupBack to the product checkerEU Safety Gate · 2026-01-01 →
Browse verified historical EU Safety Gate alerts. Every entry links to its identified official source.
The balloon contains small parts (the lip in the neck of the balloon and the confetti inside) that can easily detach. A small child may put them in the mouth and choke. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-1.
The product expands in size when in contact with water. If a child puts the product in the mouth or swallows it, contact with saliva or stomach liquids will cause the product to expand, which can result in occlusion of the respiratory tract or intestinal blockage. The product does not comply with the General Product Safety Regulation.
The top screw of the product contains an excessive amount of lead. Lead poses a risk to the environment and damage to the kidneys, the circulatory system, and the developing brain. The product does not comply with the REACH Regulation.
The thermostat of the device does not cut off the heating of the device when the maximum authorized operating temperature of 55°C is reached. It may therefore overheat and cause a fire The product does not comply with the requirements of the Low Voltage Directive nor with the European standard EN 60335-2-9.
The mains cable can be connected to the pump in reverse, allowing the live pin to connect to the earth pin and causing accessible metal parts to become live. Consequently, users could receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive.
The product contains formaldehyde (measured value up to 190 mg/kg). Formaldehyde is a skin sensitiser and can trigger allergic reactions and may cause cancer. The product does not comply with the REACH Regulation.
Due to insufficient detection capability in the Battery Management System, micro-shorts between battery cells may remain undetected. Undetected micro-shorts could cause the cells to overheat and lead to a fire while the vehicle is parked or charging. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
When the trailer is loaded close to its maximum permissible total weight, it may start to pitch at speeds of around 60 km/h. This could affect stability and increase the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective weld on the ISOFIX mounting bracket could break in the event of an accident and increase the risk of injury to children in the child seat attached to it. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective weld on the ISOFIX mounting bracket could break in the event of an accident and increase the risk of injury to children in the child seat attached to it. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective weld on the ISOFIX mounting bracket could break in the event of an accident and increase the risk of injury to children in the child seat attached to it. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
An incorrectly fitted rear coil spring may detach from the vehicle, which could affect vehicle handling and create a hazard for following traffic. This increases the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective weld on the ISOFIX mounting bracket could break in the event of an accident and increase the risk of injury to children in the child seat attached to it. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective weld on the ISOFIX mounting bracket could break in the event of an accident and increase the risk of injury to children in the child seat attached to it. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective weld on the ISOFIX bar may break in the event of an accident and increase the risk of injury to children in the child seat attached to it. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective weld on the ISOFIX bar could break in the event of an accident and increase the risk of injury to children in the child seat attached to it. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The product has small parts (the pullers of the zipper) that can easily detach. Small children may put them in the mouth and choke. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-1.
The product contains formaldehyde (measured value up to 180 mg/kg). Formaldehyde is a skin sensitiser and can trigger allergic reactions and may cause cancer. The product does not comply with the REACH Regulation.
The product has an excessive concentration of p-phenylenediamine (PPD) (measured value up to 6.5% by weight). PPD may cause an allergic skin reaction. The product does not comply with the Cosmetic Products Regulation.
According to the list of ingredients, the product contains 2-(4-tert-butylbenzyl) propionaldehyde (BMHCA), which is prohibited in cosmetic products. BMHCA may harm the reproductive system, may harm the health of the unborn child and may cause skin sensitisation. The product does not comply with the Cosmetic Products Regulation.
The product lacks sufficient insulation. The safety distances between the printed circuit board and the transformer are too small. The user could receive an electric shock. Additionally, the spacing between live parts on the printed circuit board is insufficient, which may lead to fire. The product does not comply with the requirements of the Low Voltage Directive.
In the event of an impact, the helmet could easily become detached and slip off the head of the user, leaving it exposed to injuries. The product does not comply with the Regulation ECE 22-06.
In the event of an impact, the helmet could easily become detached and slip off the head of the user, leaving it exposed to injuries. The product does not comply with the Regulation ECE 22-05.
In spite of following the filling instructions, the product overflows, leading to burns of the user. The product does not comply with the requirements of the Low Voltage Directive.
The two-pin plug does not incorporate a fuse. In the event of a fault or overcurrent, there is no adequate protection, which may lead to overheating and a risk of fire. The product does not comply with the Regulation on the approval and market surveillance of two- or three-wheel vehicles and quadricycles.
In certain combinations of socket and plug, the earthing is insufficient. When the travel adapter is used in conjunction with a Class I device, this could lead to a risk of electric shock. Moreover, the flat type C Europlug can only take a maximum load of 2.5 A. However, Class I appliances often require significantly more current, which can then lead to fire. The product does not comply with the requirements of the Low Voltage Directive.
The solders in the product have an excessive amount of lead (measured value more than 0,15% by weight). Lead poses a risk to the environment. The product does not comply with the requirements of the Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS 2 Directive).
The laser beam is too powerful (measured value up to 5.93 mW) and the projector is not properly labelled. Direct viewing of the laser beam could cause damage to sight. The product does not comply with the General Product Safety Regulation nor with the European standards EN 60825-1 and EN 50689.
The creepage distances between the primary and secondary circuits are inadequate. The user could therefore touch accessible live parts and receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive nor with the European standards EN 60335-1 and 60335-2.
The product has an excessive concentration of lead. Lead is harmful to human health, accumulates in the body, can cause developmental neurotoxicity and may affect breast-fed or unborn children. The product does not comply with the REACH Regulation.
The supplied plug does not have capacity for a fuse, which is required for safe operation under fault conditions. This could cause the plug to overheat, posing a risk of fire. Improvements are also required to product documentation and marking. The product does not comply with the Regulation on the type-approval and market surveillance of two- or three-wheel vehicles and quadricycles.
The toy has an excessive concentration of bis(2-ethylhexyl) phthalate (DEHP) and dibutyl phthalate (DBP) (measured values up to 2.86% and 0.34% by weight, respectively). These phthalates may harm the health of children, causing possibly damage to the reproductive system. The product does not comply with the REACH Regulation.
The driver-side floor mat may come into contact with the accelerator pedal while driving, causing the vehicle to maintain its speed. This could prevent the driver from properly controlling the vehicle’s speed, increasing the risk of a collision and injuries. This product does not comply with the General Product Safety Regulation.
During installation of the high-security locks, metal shavings from the B-pillar may have damaged the seatbelt. This could reduce the restraining effectiveness of the seatbelt in the event of an accident, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seat belt anchorage buckle may not lock properly, which could prevent the seat belt from adequately restraining the occupant in certain collision scenarios, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The bolts or rivets attaching the chains to the flail-cutter could break. The chains might consequently detach during use and hit the user causing injuries. The product does not comply with the requirements of the Machinery Directive nor with the Commission Decision 2012/32/EU prohibiting the placing on the market of flail-type cutting attachments for portable hand-held brush cutters.
The bolts or rivets attaching the chains to the flail-cutter could break. The chains might consequently detach during use and hit the user causing injuries. The product does not comply with the requirements of the Machinery Directive nor with the Commission Decision 2012/32/EU prohibiting the placing on the market of flail-type cutting attachments for portable hand-held brush cutters.
The product has small parts (plastic muzzle and eye) that may easily detach. Small children may put them in their mouth and choke. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-1.
The bolts or rivets attaching the chains to the flail-cutter could break. The chains might consequently detach during use and hit the user causing injuries. The product does not comply with the requirements of the Machinery Directive nor with the Commission Decision 2012/32/EU prohibiting the placing on the market of flail-type cutting attachments for portable hand-held brush cutters.
The insulation of the product and the clearance/creepage distances between the primary and secondary circuits are not sufficient. Consequently, the user may receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive nor with the European standards EN 62368 and EN 50075.
The toy contains small magnets with a high magnetic flux (value up to 1,09 T²mm²) which can be easily detached. If a child swallows the small magnets, they could attract one another causing intestinal blockage or perforation. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-1.
Manufacturing errors in the production of steering components may result in components having reduced fatigue strength or being susceptible to breakage. If one of the components breaks, the steering may fail, creating a risk of accidents. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The steering components (including steering rods, push rods and tie rods) may have a manufacturing defect. Some parts may not have been hardened correctly during production, which could make them wear out faster and become weaker over time. This could cause the part to break, especially when turning the steering wheel at low speeds. If this happens, the driver could lose control of the vehicle, increasing the risk of an accident. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The balloons release an excessive amount of nitrosatable substances(measured total value: 1.33 mg/kg). Nitrosatable substances can be absorbed through the skin and mouth while playing and generate nitrosamines. Nitrosamines may cause cancer. The product does not comply with the requirements of the Toy Safety Directive.
The toy consists of small magnets with high magnetic flux (measured value up to 351 kG²mm²). If a child swallows them, they could attract one another causing intestinal blockage or perforation. The product does not comply with the requirements of the Toy Safety Directive.
The balloons release an excessive amount of nitrosatable substances(measured total value: 2.19 mg/kg). Nitrosatable substances can be absorbed through the skin and mouth while playing and generate nitrosamines. Nitrosamines may cause cancer. The product does not comply with the requirements of the Toy Safety Directive.
Floating seats with leg openings must not have any overwater structures. In windy conditions, the float may be lifted, tipped over, pushed away, or destabilised, creating risks of falls, capsizing, separation from the caregiver, entrapment, or drowning. The product does not comply with the General Product Safety Regulation
The cross-sectional area of the cable is insufficient and the wires soldering inside the supply cable can easily deteriorate leading to risk of a short circuit, resulting in electric shock and a risk of fire. The product does not comply with the requirements of the Low Voltage Directive.
The supplied plug does not have capacity for a fuse, which is required for safe operation under fault conditions. This could cause the plug to overheat, posing a risk of fire. Improvements are also required to product documentation and marking. The product does not comply with the Regulation on the type-approval and market surveillance of two- or three-wheel vehicles and quadricycles.
Live parts of the product are easily accessible. User could touch the live parts and receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive.
The balloons release an excessive amount of nitrosatable substances (measured total value: 2.091 mg/kg). Nitrosatable substances can be absorbed through the skin and mouth while playing and generate nitrosamines. Nitrosamines may cause cancer. The product does not comply with the requirements of the Toy Safety Directive.
The supplied plug does not meet dimensional requirements and does not have capacity for a fuse, which is required for safe operation under fault conditions. These could cause the adaptor or plug to catch fire or explode, posing a risk of fire. The product does not comply with the requirements of the Machinery Directive.
The insulation of the product is inadequate. The user could therefore touch accessible live parts during light source replacement and receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive nor with the European standard EN 60598-1.
The supplied plug does not incorporate a fuse, which is required for safe operation under fault conditions. This could cause the plug to overheat, posing a risk of fire. Improvements are also required to product documentation and marking. The product does not comply with the Regulation on the type-approval and market surveillance of two- or three-wheel vehicles and quadricycles.
Incorrect tightening torque and a missing locking pin may cause the wheels to detach from the lower control arm. This could affect driving stability, increasing the risk of an accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of two- or three-wheel vehicles and quadricycles.
The plug can be partially inserted leaving a live pin exposed and the product has inadequate insulation. The user could touch accessible live parts and receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive nor with the European standards EN 60598-1 and EN 60598-2-20.
The cable is not properly anchored (missing cable strain relief) and the accessible wires have inadequate insulation. Moreover, the plug can be partially inserted leaving a live pin exposed. The user could touch accessible live parts and receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive nor with the European standards EN 60598-1 and EN 60598-2-20.
The product is supplied with a two-pin plug that cannot incorporate a fuse and therefore does not meet the required safety specifications. In the event of a fault or overcurrent, the absence of adequate protection could lead to overheating, increasing the risk of fire. The product does not comply with the requirements of the Machinery Directive.
The passenger van has uneven material strength in certain areas of the bonnet. In the event of a collision with a pedestrian, this could reduce the bonnet’s ability to absorb impact energy and increase the severity of injuries to the pedestrian. The product does not comply with the Regulation on the approval and market surveillance of two- or three-wheel vehicles and quadricycles.
The puzzle mat pieces can easily break while a child is playing, generating small parts. Children may put these in the mouth and choke. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-1.
The product has an excessive volume of nicotine-containing liquid (measured value: 2.3 ml). This could lead to the accidental consumption of a high dose of nicotine. Nicotine is acutely toxic and can endanger the user’s safety, notably if the product comes into contact with the skin or is ingested. The product does not comply with the requirements of the Tobacco Products Directive.
The product contains benzyl alcohol, but the presence is not indicated in the list of ingredients. Consumers are not aware of their presence, and may suffer allergic reactions or skin sensitisation. The product does not comply with the Cosmetic Products Regulation.
The product has an excessive concentration of benzoic acid (measured value: 0.76 %). Benzoic acid causes skin irritation. The product does not comply with the Cosmetic Products Regulation.
The migration of boron from the toy slime is too high (measured value up to 502 mg/kg). Ingestion or contact with an excessive quantity of boron may harm the health of children by damaging their reproductive system. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-3.
The rated current of the plug is lower than the rated current of the socket. Consequently, the device may overheat and cause fire or burns. Moreover, the clearance and creepage distances between plug pin and grounding are inadequate, which may cause electric shock to the user. The product does not comply with the requirements of the Low Voltage Directive nor with the European standard EN 60884-2.
The electrical resistance of the shoes is too high (measured value: 7,4x10^9 Ω), which could cause static charge accumulating on the user's body and could damage electronic components next to it. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 20345.
The structure of the socket allows single-pole insertion of plugs and the protection surface of the plug's face is insufficient. Moreover, the wires can be pulled or twisted out of their terminals and the single-layer insulation is insufficient for a Class II appliance, which could lead to exposed live parts. Finally, the insulation does not ensure adequate separation from live (active) parts during the lifetime of the luminaire. The user could touch accessible live parts and receive an electric shock. The product does not comply with the requirements of the Low Voltage Directive nor with the European standards EN 60598-1 and EN 60598-2.
Inside the device, some electrical parts (such as components or circuits) are not sufficiently distant from each other. Moreover, the device is missing one of the safety capacitors to prevent electricity leakage between hazardous and accessible parts. Additionally, the cable connecting the device to the electrical socket has a different number of pins between the plug (wall side) and the connector (device side). This may cause a poor connection and increase the risk of overheating or an electric shock. The product does not comply with the requirements of the Low Voltage Directive.
Pillows and soft toys are advised not to be placed in the sleep space for babies under the age of one year as their presence increases the risk of overheating and airway obstruction, which have been associated with sudden infant death syndrome (SIDS). The product may lead to suffocation when used in a sleep space for babies. The product does not comply with the General Product Safety Regulation.
The supplied plug does not meet dimensional requirements and does not have capacity for a fuse, which is required for safe operation under fault conditions. Moreover, the earth pin of the adaptor is not sufficient. These could cause the adaptor or plug to catch fire or explode, posing a risk of fire. The product does not comply with the requirements of the Low Voltage Directive.
According to the label, the product contains a psychoactive cannabinoid (Hexahydrozepine). The use of this substance is associated with the risk of mental and behavioural disorders. The product does not comply with the General Product Safety Regulation.
The plastic material of the product has an excessive concentration of bis(2-ethylhexyl) phthalate (DEHP) and dibutyl phthalate (DBP) (measured values: 6.2% and 0.02% by weight, respectively). These phthalates may harm the health of children, causing possible damage to their reproductive system. The product does not comply with the requirements of the Toy Safety Directive.
When using the self-feeding bottle, a baby does not have the dexterity or cognitive ability to control the flow of bottle feed, to know when to stop feeding, or to act if they gag or choke or to otherwise signal or raise alarm if something is going wrong. This can lead to choking. The product does not comply with the General Product Safety Regulation.
During normal use and following the filling instructions the product overflows, leading to burns of the user. The product does not comply with the requirements of the Low Voltage Directive.
The product has a protruding part that is too long. Small children may put it in the mouth and choke. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-1.
The strap in front of the ear may slide backwards, which could affect the stability and optimal hold of the helmet on the head during normal use. In case of an accident this may lead to injuries. The product does not comply with the Personal Protective Equipment Regulation.
The product resembles a toy; however, there is a risk of drowning if children play with it unsupervised. Floating seats with leg openings must be used under constant adult supervision and must not have any play elements or overwater structures. The product does not meet the requirements of the General Product Safety Regulation nor with the European standard EN 13138.
The product contains cannabidiol and delta-9-tetrahydrocannabinol (measured value up to 0.5 and 0. 3% by weight, respectively), which are psychoactive substances that can cause central nervous system disorders. The product does not comply with the Cosmetic Products Regulation.
The spoons can easily break, generating small parts. Small children could put them in the mouth and choke. The product does not comply with the General Product Safety Regulation.
The product has aromatic amines. When in direct and prolonged contact with the skin, the aromatic amines may be absorbed by the skin. Aromatic amines can cause cancer, cell mutations and affect reproduction. The product does not comply with the REACH Regulation.
The propellant in the driver and front passenger airbags may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver and front passenger airbags may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.
In the event of an impact, the helmet could easily become detached and slip off the head of the user, leaving it exposed to injuries. The product does not comply with the Regulation ECE 22-06.
In the event of an impact, the helmet could easily become detached and slip off the head of the user, leaving it exposed to injuries. The product does not comply with the Regulation ECE 22-06.
Due to a mistranslation of the configuration data between two production systems, the vehicle’s body control module (BCM) may not be correctly configured to detect indicator light failures. If an indicator bulb fails, the BCM may not detect the fault and the warning signal may not illuminate, reducing communication with other road users and increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a mistranslation of the configuration data between two production systems, the vehicle’s body control module (BCM) may not be correctly configured to detect indicator light failures. If an indicator bulb fails, the BCM may not detect the fault and the warning signal may not illuminate, reducing communication with other road users and increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a mistranslation of the configuration data between two production systems, the vehicle’s body control module (BCM) may not be correctly configured to detect indicator light failures. If an indicator bulb fails, the BCM may not detect the fault and the warning signal may not illuminate, reducing communication with other road users and increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a mistranslation of the configuration data between two production systems, the vehicle’s body control module (BCM) may not be correctly configured to detect indicator light failures. If an indicator bulb fails, the BCM may not detect the fault and the warning signal may not illuminate, reducing communication with other road users and increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag connectors in the steering column has shown that they may corrode. Over time, the airbag might not deploy as intended and therefore could increase the risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The toy has small parts (the suction cups) that can easily detach. A small child could put them in their mouth and choke. The product does not comply with the requirements of the Toy Safety Directive.
The plastic material of the toy has an excessive amount of di-‘isononyl’ phthalate (DINP) (measured value: 23.6% by weight). DINP may harm the health of children by causing possible damage to their reproductive system. The product does not comply with the requirements of the Toy Safety Directive nor with the REACH Regulation.
The migration of boron from the toy slime is too high (measured value up to 795 mg/kg). Ingestion or contact with an excessive quantity of boron may harm the health of children by damaging their reproductive system. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-3.
The solders in the product have an excessive amount of lead (measured value 0.15% by weight). Lead poses a risk to the environment. The product does not comply with the requirements of the Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS 2 Directive).
The toy contains small magnets with a high magnetic flux (value up to 50,74 kG²mm²) which can be easily detached. If a child swallows the small magnets, they could attract one another causing intestinal blockage or perforation. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-1.
The product has an excessive concentration of polycyclic aromatic hydrocarbons (PAHs), notably benzo(a)pyrene (measured value: 0.000014 % by weight). Benzo[a]pyrene may cause cancer and is also mutagenic and toxic for reproduction. The product does not comply with the REACH Regulation.
The migration of boron from the toy slime is too high (measured value: up to 668.28 mg/kg). Ingestion or contact with an excessive quantity of boron may harm the health of children by damaging their reproductive system. The product does not comply with the requirements of the Toy Safety Directive nor with the relevant European standard EN 71-3.
The plastic material of the product has an excessive concentration of bis(2-ethylhexyl) phthalate (DEHP) and dibutyl phthalate (DBP). These phthalates may harm the health by causing possible damage to the reproductive system. Additionally, the product has an excessive concentration of short chain chlorinated paraffins (SCCPs). SCCPs persist in the environment, are toxic to aquatic organisms at low concentrations and bio-accumulate in wildlife and humans, posing a risk to human health and the environment. The product does not comply with the REACH Regulation nor with the Persistent Organic Pollutants (POP) Regulation.
The laser beam is too powerful. Direct viewing of the laser beam could cause damage to sight. The product does not comply with the General Product Safety Regulation nor with the European standards EN 50689 and EN 60825-1.
The supplied plug does not meet dimensional requirements and cannot make a secure connection with the socket. Additionally, the supplied cord is not suitable for outdoor use and will deteriorate in the sun. Consequently, the product could overheat and catch fire. The product does not comply with the requirements of the Low Voltage Directive.